Skip to product information
Steife Kupplungsfeder / Klappenfeder für Klappenauspuff Stellmotoren - WEHRAN MOTORSPORT
1/2

Exhaust Valve Actuator Spring – Stiff Replacement Spring for Küster Actuators

Item No.: WM-UNI-020

€28,90 EUR
Kunde 1
Unsere Teile sind Verbaut in Projekten von strasse.sport und 249+ weiteren Builds

✔ universal for many vehicles
✔ easy installation
✔ solution for rattling flaps
✔ corrosion-resistant

The exhaust valve actuator spring from Wehran Motorsport replaces the worn original spring in your exhaust valve actuator. Is your exhaust valve rattling, not opening or closing properly, or not working at all? The cause is often a worn-out or broken spring. This stiff replacement spring restores the connection between actuator and valve, and it’s an affordable alternative to replacing the entire actuator.

Exhaust valve rattle: the actuator spring is often the culprit

On many active exhaust systems, the original spring wears over time. Heat, vibration and constant valve movement cause it to fatigue, break or lose its preload. The result is play in the exhaust flap, an audible rattle or a valve that no longer operates correctly. The new spring restores the tension the mechanism needs, so the valve works cleanly again.

Fits Küster exhaust valve actuators

The spring is suitable for Küster exhaust valve actuators, which are used in many cars with active or valved exhaust systems, for example:

  • suitable for BMW F and G Series
  • suitable for VW Golf 7 / Golf 8 GTI
  • suitable for Audi S3 / RS3
  • suitable for Hyundai i30N
  • suitable for Kia Ceed / ProCeed GT

Please check before ordering that your car or exhaust system uses a Küster actuator.

Simple DIY fix instead of a new actuator

Replacing the spring is usually quick and can be done yourself with some technical know-how. You only replace the faulty original spring and keep using the actuator, as long as it still works. That saves you the much higher cost of a new actuator.

Coated and corrosion-resistant

The spring is coated and corrosion-resistant, so it’s well protected against moisture, dirt and heat around the exhaust system. Its spring properties stay stable even with frequent use of the valve control.

What’s included

  • 1× exhaust valve actuator spring

Note: The spring only replaces the faulty or worn original spring in the actuator. Please make sure before ordering that your actuator is compatible and that the rattle is actually caused by the spring.

Aftermarket accessory by Wehran Motorsport; not an original part of the vehicle manufacturers named or of Küster, and not affiliated with them.

Product safety information / manufacturer's information:

WEHRAN MOTORSPORT
Christophorusweg 8
45659 Recklinghausen
+4915568344237
info@wehranmotorsport.com

Warranty & Manufacturer's Guarantee

Your legal guarantee rights

Frequently asked questions about the product

How can I tell if the flap spring in the exhaust flap actuator is defective?

Typical symptoms include a non-functional exhaust flap, loud rattling in the flap exhaust system, or noticeable play in the actuator. Often, the original spring is worn out, broken, or has lost its preload.

Which vehicles is the exhaust flap spring suitable for?

The flap spring is universally suitable for Küster actuators and can be used in many vehicles with flap exhaust systems, such as BMW F and G Series, VW Golf 7/8 GTI, Audi S3/RS3, Hyundai i30N, and Kia Ceed and ProCeed GT. It is important that a compatible Küster actuator is installed.

Can I install the flap stay myself?

Yes, the replacement usually takes a few minutes and requires a bit of technical understanding. The defective original spring is replaced with the new clutch spring, without the need to replace the entire actuator.

You might also like this